LME:
2.698,07 €
-0,48 %
-13,1100 €
HUF/EUR:
363,72
-0,14 %
-0,5000 Ft
HUENDEROHRSK
Log in |
ACH
LME: 2.698,07 € ↘︎ -0,48 % -13,1100 €
HUF/EUR: 363,72 ↘︎ -0,14 %
Log in
HUENDEROHRSK
EN AW 5083 (AlMg4,5Mn0,7) rolled aluminium plate
Rolled aluminium plates

EN AW 5083 (AlMg4,5Mn0,7) rolled aluminium plate

One of the most versatile alloy grades, provided that tensile strength is not a critical requirement.

  • Excellent corrosion resistance – optimised for saline/outdoor environments.
  • Very good weldability – low cracking tendency, stable weld quality.
  • Medium strength
  • Technical anodising is possible; in decorative anodising the appearance may be limited.
Field of use
  • Food industry
  • Worktops and table tops
  • Machine and component manufacturing
  • Shipbuilding
Alloy grade
EN AW 5083 (AlMg4,5Mn0,7)
Tempers
O / H111 (soft)
Thicknesses
Available sizes are listed on the product datasheets.
Formats
Plate / coil / slit strip
Besides the rolled execution, typically also available as cast + milled

EN AW-5083 – chemical composition1

(EN 573-3)

Specifications (%)

Remainder: Aluminium

 Others
Si Fe Cu Mn Mg Cr Ni Zn Ti Ga V Notes Each Total2
0,40 0,40 0,10 0,40 - 1,00 4,00 - 4,90 0,05 - 0,25 - 0,25 0,15 - - - 0,05 0,15
1 Chemical specifications are in mass %. Where no range is given, the alloying content is the maximum value.
2 Includes all elements for which no separate limit is specified.

EN AW-5083 – mechanical properties (H111)

DIN EN 485-2:2009-01
EN 485-2:2008 – Al Mg4,5 Mn0,7

Temper Nominal thickness
t [mm]		 Tensile strength
Rm min.–max. [MPa]		 Proof strength
Rp0,2 min.–max. [MPa]		 Elongation
A50 min. [%]		 Bend factor 90°
rmin [·t]		 Hardness
HBW
H111 0,2 – 0,5 275 – 350 125 – — 11 1,0 · t 75
0,5 – 1,5 275 – 350 125 – — 12 1,0 · t 75
1,5 – 3,0 275 – 350 125 – — 13 1,0 · t 75
3,0 – 6,3 275 – 350 125 – — 15 1,5 · t 75
6,3 – 12,5 270 – 345 115 – — 16 2,5 · t 75
12,5 – 50,0 270 – 345 115 – — 15 — 75
50,0 – 80,0 270 – 345 115 – — 14 — 73
80,0 – 120,0 260 – — 110 – — 12 — 70
120,0 – 200,0 255 – — 105 – — 12 — 69
200,0 – 300,0 245 – — 90 – — 9 — 69

Notes:
• The table is an extract of the official EN 485-2 values.
• The bend radius (rmin) is an indicative value according to the standard.
• HBW: Brinell hardness measured with a carbide ball.

EN AW-5083 – Al Mg4,5 Mn0,7 – general alloy grade information

The values and data below are indicative – they help to give a general picture of the material.

Alloy designations

EN AWAl Mg4,5 Mn0,7
Old designationAl Mg4,5 Mn
Material number (DIN)3.3547
United Kingdom (BS)N8
Italy (UNI)9005/5
SpainL-3321
Sweden144140
Norway17215
France (AFNOR)A-G4,5MC
Colour code RAL 8002   Signal Brown

Typical physical properties

Density [g/cm3]2,66
Modulus of elasticity [GPa]71
Thermal conductivity [W/m*K]110 – 140
Thermal expansion coefficient [K-1*10-6] -50°C – 20°C   |   22,3
20°C – 100°C   |   24,2
20°C – 200°C   |   25,0
20°C – 300°C   |   26,0
Specific heat [J/(kg*K)]900
Electrical conductivity [m/Ω*mm2]16 – 19
Shear modulus [GPa]26,8
Machinability
Annealed3
Work-hardened2
Heat-treated-
Dimensional stability2
EDM1
Surface treatment
Anodising – protective2
Special anodising quality (EQ)-
Anodising – decorative4
Painting / coating4
Polishing2
Weldability
Process Value Filler metal
Gas3 – 4SG-Al 5183
TIG2SG-Al 5356
MIG2SG-Al 5087
Resistance welding2-
Solderability
Brazing with flux4 – 5
Brazing without flux4 – 5
Abrasion soldering3
Soft soldering with flux4 – 5
Corrosion resistance
Normal atmosphere1
Marine environment1
Formability
Cold forming Value Delivery temper
Bending2
Compression forming4
Deep drawing2O
Upsetting2 – 3O
Impact extrusion4
Hot forming
Closed-die forging4 – 5
Extrusion4
Hammer forging4
Food-contact use (DIN EN 602) yes

Legend

1very good
2good
3medium
4poor
5not suitable
EQ Anodising quality must be ordered separately and confirmed in writing

Thickness tolerances for rolled plates

EN 485-3:2003

Nominal thickness
t [mm] 		Thickness tolerances by nominal plate width
[mm]
≤ 1 250 > 1 250 – 1 600 > 1 600 – 2 000 > 2 000 – 2 500 > 2 500 – 3 500
≥ 2,5 – 4 ± 0,28 ± 0,28 ± 0,32 ± 0,35 ± 0,40
4 – 5 ± 0,30 ± 0,30 ± 0,35 ± 0,40 ± 0,45
5 – 6 ± 0,32 ± 0,32 ± 0,40 ± 0,45 ± 0,50
6 – 8 ± 0,35 ± 0,40 ± 0,40 ± 0,50 ± 0,55
8 – 10 ± 0,45 ± 0,50 ± 0,50 ± 0,55 ± 0,60
10 – 15 ± 0,50 ± 0,60 ± 0,65 ± 0,65 ± 0,80
15 – 20 ± 0,60 ± 0,70 ± 0,75 ± 0,80 ± 0,90
20 – 30 ± 0,65 ± 0,75 ± 0,85 ± 0,90 ± 1,0
30 – 40 ± 0,75 ± 0,85 ± 1,0 ± 1,1 ± 1,2
40 – 50 ± 0,90 ± 1,0 ± 1,1 ± 1,2 ± 1,5
50 – 60 ± 1,1 ± 1,2 ± 1,4 ± 1,5 ± 1,7
60 – 80 ± 1,4 ± 1,5 ± 1,7 ± 1,9 ± 2,0
80 – 100 ± 1,7 ± 1,8 ± 1,9 ± 2,1 ± 2,2
100 – 150 ± 2,1 ± 2,2 ± 2,5 ± 2,6 —
150 – 220 ± 2,5 ± 2,6 ± 2,9 ± 3,0 —
220 – 350 ± 2,8 ± 2,9 ± 3,2 ± 3,3 —
350 – 400 ± 3,5 ± 3,7 ± 3,9 ± 4,2 —

Thickness tolerances for rolled plates

EN 485-3:2003

Nominal thickness
t [mm] 		Thickness tolerances by nominal plate width
[mm]
≤ 1 250 > 1 250 – 1 600 > 1 600 – 2 000 > 2 000 – 2 500 > 2 500 – 3 500
≥ 2,5 – 4 ± 0,28 ± 0,28 ± 0,32 ± 0,35 ± 0,40
4 – 5 ± 0,30 ± 0,30 ± 0,35 ± 0,40 ± 0,45
5 – 6 ± 0,32 ± 0,32 ± 0,40 ± 0,45 ± 0,50
6 – 8 ± 0,35 ± 0,40 ± 0,40 ± 0,50 ± 0,55
8 – 10 ± 0,45 ± 0,50 ± 0,50 ± 0,55 ± 0,60
10 – 15 ± 0,50 ± 0,60 ± 0,65 ± 0,65 ± 0,80
15 – 20 ± 0,60 ± 0,70 ± 0,75 ± 0,80 ± 0,90
20 – 30 ± 0,65 ± 0,75 ± 0,85 ± 0,90 ± 1,0
30 – 40 ± 0,75 ± 0,85 ± 1,0 ± 1,1 ± 1,2
40 – 50 ± 0,90 ± 1,0 ± 1,1 ± 1,2 ± 1,5
50 – 60 ± 1,1 ± 1,2 ± 1,4 ± 1,5 ± 1,7
60 – 80 ± 1,4 ± 1,5 ± 1,7 ± 1,9 ± 2,0
80 – 100 ± 1,7 ± 1,8 ± 1,9 ± 2,1 ± 2,2
100 – 150 ± 2,1 ± 2,2 ± 2,5 ± 2,6 —
150 – 220 ± 2,5 ± 2,6 ± 2,9 ± 3,0 —
220 – 350 ± 2,8 ± 2,9 ± 3,2 ± 3,3 —
350 – 400 ± 3,5 ± 3,7 ± 3,9 ± 4,2 —
Hengerelt alumínium vastaglemez
Hengerelt alumínium vastaglemez
Hengerelt alumínium vastaglemez
Hengerelt alumínium vastaglemez
Hengerelt alumínium vastaglemez
Hengerelt alumínium vékonylemez
Back to the previous page
Note: We accept no liability or warranty for the correctness, accuracy or completeness of the information and data stated above. Standards and indicative values may change. Agreements are valid as set out in the quotation / order confirmation. We also draw attention to the fact that we accept no liability for colour shades arising during decorative anodising, or for corrosion-resistance results and how they develop. Individual terms may be agreed on a case-by-case basis and must be recorded in writing.