LME:
2.698,07 €
-0,48 %
-13,1100 €
HUF/EUR:
363,72
-0,14 %
-0,5000 Ft
HUENDEROHRSK
Log in |
ACH
LME: 2.698,07 € ↘︎ -0,48 % -13,1100 €
HUF/EUR: 363,72 ↘︎ -0,14 %
Log in
HUENDEROHRSK
EN AW-2007 (AlCuMgPb) aluminium round bar
Aluminium round bars

EN AW-2007 (AlCuMgPb) aluminium round bar

Excellent machinability, good strength in heat-treated tempers, for automatic turning and high-volume precision parts.

  • Outstanding machinability
  • Produces fine, broken chips
  • Only limited suitability for anodising
  • Typically a German-market alloy
Field of use
  • Machine manufacturing
  • Toolmaking
  • Screws and accessories
Alloy grade
EN AW-2007 (AlCuMgPb)
Tempers
T3 / T4
Formats
Bar stock – extruded, drawn execution

EN AW-2007 – chemical composition1

(EN 573-3)

Specifications (%)

Remainder: Aluminium

 Others
Si Fe Cu Mn Mg Cr Ni Zn Ti Ga V Notes Each Total2
0,80 0,80 3,30 - 4,60 0,50 - 1,00 0,40 - 1,80 0,10 0,20 0,80 0,20 - - 0,20 Bi • 0,80 – 1,5 Pb • 0,20 Sn 0,10 0,30
1 Chemical specifications are in mass %. Where no range is given, the alloying content is the maximum value.
2 Includes all elements for which no separate limit is specified.

EN 754-2 – Mechanical properties: round bars (drawn)

The values below are indicative.

Delivery temper Diameter (mm) Tensile strength Rm (MPa) Proof strength Rp0,2 (MPa) Elongation (% min.) Hardness9
HBW
min. max. min. max. A50 mm A
T3 ≤ 30 370 – 240 – 5 7 95
> 30 340 – 220 – – 6 95
T351 ≤ 80 370 – 240 – 3 5 95

EN 755-2 – Mechanical properties: round bars (extruded)

The values below are indicative.

Delivery temper Diameter (mm) Tensile strength Rm (MPa) Proof strength Rp0,2 (MPa) Elongation (% min.) Hardness9
HBW
min. max. min. max. A50 mm A
T4 ≤ 80 370 – 250 – 6 8 95
T4510 ≤ 80 340 – 220 – – 8 95
T4511 > 80 330 – 210 – – 7 95
9 Hardness (HBW) values are indicative.
Note: for larger diameters (e.g. > 80 mm, or > 200 mm) available values/tempers may differ by manufacturer – please consult us if needed.

EN AW-2007 – general alloy grade information

The values and data below are indicative – they help to give a general picture of the material.

Alloy designations

EN AWAl Cu4 Pb Mg Mn
Old designationAl Cu Mg Pb
Material number (DIN)3.1645
United Kingdom (BS)-
Italy (UNI)9002/8
Spain-
Sweden-
Norway17110
France (AFNOR)-
Colour code RAL 9004   Signal black

Typical physical properties

Density [g/cm3] 2,85
Modulus of elasticity [GPa] 72,5
Thermal conductivity [W/m*K] 130 – 160
Thermal expansion coefficient [K-1*10-6] -50°C – 20°C –
20°C – 100°C 23,0
20°C – 200°C –
20°C – 300°C –
Specific heat [J/(kg*K)] 860
Electrical conductivity [m/Ω*mm2] 18 – 22
Shear modulus [GPa] 27,3

Heat treatment – annealing / recrystallisation annealing

Annealing temperature380°C – 420°C
Heat-up time1 – 2 hours
Cooling conditions30°C/hour to 250°C, air below 250°C

Heat treatment – hardening

Solution heat treatment480°C – 490°C
Quenchingwater up to 65°C
Natural ageing5 – 8 days
Artificial ageing-
Machinability
Annealed-
Work-hardened-
Heat-treated1
Dimensional stability2
EDM1
Surface treatment
Anodising – protective4 – 5
Special anodising quality (EQ)-
Anodising – decorative5
Painting / coating4
Polishing3
Weldability
Process Value Filler metal
Gas--
TIG--
MIG--
Resistance welding--
Solderability
Brazing with flux5
Brazing without flux5
Abrasion soldering4 – 5
Soft soldering with flux-
Corrosion resistance
Normal atmosphere / weathering conditions4 – 5
Marine atmosphere4 – 5
Formability
Cold forming Value Delivery temper
Bending4 – 5
Compression forming-
Deep drawing (temper-dependent)-
Upsetting (temper-dependent)4 – 5
Impact extrusion-
Hot forming
Closed-die forging-
Extrusion4
Hammer forging-
Food-contact use (DIN EN 602) no

Legend

1very good
2good
3medium
4poor
5not suitable
EQ Anodising quality must be ordered separately and confirmed in writing

Dimensional tolerances of extruded round bars

DIN EN 755-4 : 2008

Alloy groups

Group I EN AW-1050A, EN AW-1070A, EN AW-1200, EN AW-1350
EN AW-3102, EN AW-3003, EN AW-3103
EN AW-5005, EN AW-5005A, EN AW-5051A, EN AW-5251
EN AW-6101A, EN AW-6101B, EN AW-6005, EN AW-6005A, EN AW-6106, EN AW-6008, EN AW-6010A, EN AW-6012, EN AW-6014, EN AW-6018, EN AW-6023, EN AW-6351, EN AW-6060, EN AW-6360, EN AW-6061, EN AW-6261, EN AW-6262, EN AW-6262A, EN AW-6063, EN AW-6063A, EN AW-6463, EN AW-6065, EN AW-6081, EN AW-6082, EN AW-6182
Group II EN AW-2007, EN AW-2011, EN AW-2011A, EN AW-2014, EN AW-2014A
EN AW-2017A, EN AW-2024, EN AW-2030
EN AW-5019, EN AW-5049, EN AW-5052, EN AW-5154A, EN AW-5454, EN AW-5754, EN AW-5083, EN AW-5086
EN AW-7003, EN AW-7005, EN AW-7108, EN AW-7108A, EN AW-7020, EN AW-7021, EN AW-7022, EN AW-7049A, EN AW-7075

Diameter tolerances (extruded – EN 755)

Dimensions in millimetres (mm)
Ø mm Tolerances
from to Alloy group I Alloy group II
≥ 1018± 0,22± 0,30
1825± 0,25± 0,35
2540± 0,30± 0,40
4050± 0,35± 0,45
5065± 0,40± 0,50
6580± 0,45± 0,70
80100± 0,55± 0,90
100120± 0,65± 1,0
120150± 0,80± 1,2
150180± 1,0± 1,4
180220± 1,15± 1,7
Note: For tolerances outside the sizes above, please ask our sales team.

Dimensional tolerances of extruded round bars

DIN EN 755-4 : 2008

Alloy groups

Group I EN AW-1050A, EN AW-1070A, EN AW-1200, EN AW-1350
EN AW-3102, EN AW-3003, EN AW-3103
EN AW-5005, EN AW-5005A, EN AW-5051A, EN AW-5251
EN AW-6101A, EN AW-6101B, EN AW-6005, EN AW-6005A, EN AW-6106, EN AW-6008, EN AW-6010A, EN AW-6012, EN AW-6014, EN AW-6018, EN AW-6023, EN AW-6351, EN AW-6060, EN AW-6360, EN AW-6061, EN AW-6261, EN AW-6262, EN AW-6262A, EN AW-6063, EN AW-6063A, EN AW-6463, EN AW-6065, EN AW-6081, EN AW-6082, EN AW-6182
Group II EN AW-2007, EN AW-2011, EN AW-2011A, EN AW-2014, EN AW-2014A
EN AW-2017A, EN AW-2024, EN AW-2030
EN AW-5019, EN AW-5049, EN AW-5052, EN AW-5154A, EN AW-5454, EN AW-5754, EN AW-5083, EN AW-5086
EN AW-7003, EN AW-7005, EN AW-7108, EN AW-7108A, EN AW-7020, EN AW-7021, EN AW-7022, EN AW-7049A, EN AW-7075

Diameter tolerances (extruded – EN 755)

Dimensions in millimetres (mm)
Ø mm Tolerances
from to Alloy group I Alloy group II
≥ 1018± 0,22± 0,30
1825± 0,25± 0,35
2540± 0,30± 0,40
4050± 0,35± 0,45
5065± 0,40± 0,50
6580± 0,45± 0,70
80100± 0,55± 0,90
100120± 0,65± 1,0
120150± 0,80± 1,2
150180± 1,0± 1,4
180220± 1,15± 1,7
Note: For tolerances outside the sizes above, please ask our sales team.
EN AW-2007 (AlCuMgPb) aluminium round bar
EN AW-2007 (AlCuMgPb) aluminium round bar
EN AW-2007 (AlCuMgPb) aluminium round bar
Back to the previous page
Note: We accept no liability or warranty for the correctness, accuracy or completeness of the information and data stated above. Standards and indicative values may change. Agreements are valid as set out in the quotation / order confirmation. We also draw attention to the fact that we accept no liability for colour shades arising during decorative anodising, or for corrosion-resistance results and how they develop. Individual terms may be agreed on a case-by-case basis and must be recorded in writing.